.
.
 
Search
 
Laminate Trimmers
Trend Routing > Router Cutters > Laminate Trimmers
  Returned 20 Results
TREND 46/06X1/4TC COMBI TRIMMER A1=90¡ X A2=45¡
TREND 46/06X1/4TC COMBI TRIMMER A1=90¡ X A2=45¡

A self-guided combination trimmer. A 90 degree trim is obtained by engaging the bottom half. A 45 degree trim is obtained by lowering the cutter. ... More Info

£11.45 INC VAT
TREND 46/6BX1/4TC BEVEL TRIM A=45¡ X 27MM DIA
TREND 46/6BX1/4TC BEVEL TRIM A=45¡ X 27MM DIA

Cut a wider edge line, at an angle of 45 degrees. A 16mm bearing is supplied as standard. A larger 19mm bearing will spread the wear of the cutting e... More Info

£63.62 INC VAT
TREND 46/6CX1/4TC BEVEL TRIM A=30¡ X 26MM DIA
TREND 46/6CX1/4TC BEVEL TRIM A=30¡ X 26MM DIA

Cut a wider edge line, at an angle of 30 degrees. A 16mm bearing is supplied as standard. A larger 19mm bearing will spread the wear of the cutting e... More Info

£57.38 INC VAT
TREND 46/7/50X1/4TC B/GUIDED GLAZING BAR 10MM RAD
TREND 46/7/50X1/4TC B/GUIDED GLAZING BAR 10MM RAD

The glazing bar ovolo cutter is bearing guided to speed setting-up and to enable curved frames to be moulded. Dimensions: D=28 mm C=19 mm B=12.7 mm R... More Info

£99.04 INC VAT
TREND 46/75X1/2TC B/GUIDED CLASSIC 6.3MM RAD
TREND 46/75X1/2TC B/GUIDED CLASSIC 6.3MM RAD

Self guiding classic cutters with facility to change profile by fitting larger bearing and varying the depth. Supplied with two bearings. Dimensions... More Info

£76.16 INC VAT
TREND 46/7X1/4TC DOUBLE OVERLAP A=90¡ X 18MM DIA
TREND 46/7X1/4TC DOUBLE OVERLAP A=90¡ X 18MM DIA

Trimming top and bottom surfaces simultaneously with bearing following the board. Two fluted. Increased productivity. Dimensions: D=18 mm C... More Info

£87.12 INC VAT
TREND 47/2X1/4TC TRIMMER A-90¡ X 18MM DIA
TREND 47/2X1/4TC TRIMMER A-90¡ X 18MM DIA

For trimming the lipping of plastic overlay, and for rebating and machining wood, Duralium and plastics. Tungsten Carbide Tipped. Use at speed 12000... More Info

£56.20 INC VAT
TREND 47/40X1/2TC PIERCE & TRIM 12.7MM DIA TWO FLUTE
TREND 47/40X1/2TC PIERCE & TRIM 12.7MM DIA TWO FLUTE

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Dimensions: D... More Info

£61.74 INC VAT
TREND 47/4X1/4TC PIERCE & TRIM 6.3MM DIA 257123
TREND 47/4X1/4TC PIERCE & TRIM 6.3MM DIA 257123

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Single fluted.... More Info

£30.94 INC VAT
TREND 47/50SX1/2TC PIERCE & TRIM 1.27MM X 123MM OL
TREND 47/50SX1/2TC PIERCE & TRIM 1.27MM X 123MM OL

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Specially desi... More Info

£77.24 INC VAT
TREND 47/50X1/2TC PIERCE & TRIM 12.7MM DIA
TREND 47/50X1/2TC PIERCE & TRIM 12.7MM DIA

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Will trim bott... More Info

£77.24 INC VAT
TREND S47/4X1/4STC PIERCE/TRIM 6.3MM DIA X 20MM CUT
TREND S47/4X1/4STC PIERCE/TRIM 6.3MM DIA X 20MM CUT

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Single fluted.... More Info

£59.20 INC VAT
TREND S47/70X1/4STC ECONOMY TRIM A=60¡X6.3MM DIA 257121
TREND S47/70X1/4STC ECONOMY TRIM A=60¡X6.3MM DIA 257121

Solid Tungsten Carbide economy cutter. For use on short runs at 90 degree or 60 degree with Ref. S47/70, at 90 degree or 83 degrees with Ref. S47/71... More Info

£53.46 INC VAT
TREND S47/71X1/4STC ECONOMY TRIM 7 DEG BEVEL
TREND S47/71X1/4STC ECONOMY TRIM 7 DEG BEVEL

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/41... More Info

£48.42 INC VAT
TREND S47/72X1/4STC ECONOMY V GROOVE 45 DEG
TREND S47/72X1/4STC ECONOMY V GROOVE 45 DEG

Cutter for trimming and bevelling timber, lippings and plastic laminate. Can only be used in laminate trimming routers, or when straight fence guides ... More Info

£48.42 INC VAT
TREND S48/39X1/4STC ECONOMY TRIM A=90¡X6.3MM DIA X 38MM
TREND S48/39X1/4STC ECONOMY TRIM A=90¡X6.3MM DIA X 38MM

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/41... More Info

£48.42 INC VAT
TREND S48/40X1/4STC ECONOMY TRIM A=90¡X6.3DX52MM 257122
TREND S48/40X1/4STC ECONOMY TRIM A=90¡X6.3DX52MM 257122

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/41... More Info

£55.86 INC VAT
TREND S48/41X1/4STC ECONOMY 7 DEG TRIM GUIDED 6.35MM DI
TREND S48/41X1/4STC ECONOMY 7 DEG TRIM GUIDED 6.35MM DI

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/41... More Info

£48.42 INC VAT
TREND S48/42X1/4STC ECONOMY FLUSH & TRIM 6.35MM GUIDED
TREND S48/42X1/4STC ECONOMY FLUSH & TRIM 6.35MM GUIDED

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/41... More Info

£48.42 INC VAT
TREND S64/2X1/4STC Guided spiral upcut 6.3x25.4mm 1/4\" Shank
TREND S64/2X1/4STC Guided spiral upcut 6.3x25.4mm 1/4" Shank

Two fluted upcut spiral cutter with guide bearing Ideal for timming into tight corners. Dimensions:  D=6.35 mm  C=25.4 mm B=6.3 m... More Info

£24.00 INC VAT
 
Terms & Conditions